自動式蒸汽調節閥
電動式溫度自動調節閥
Electric Automalic Temperature Regulating Valve

自動式蒸汽調節閥
Self Aeting Temperature Regulating Valve

概述 Introduction

蒸氣溫度調節器(以下簡稱蒸汽調溫器)是由感溫器和蒸汽(熱水、熱油)調節閥兩個部套組合構成,根據被加熱介質(水或油)的溫度變化自動調節加熱介質(蒸汽、熱水、熱油)的流量,廣泛應用于各類船用、陸用加熱裝置的蒸汽調節。

This steam temperature controller is composed of two components of temperature sensor and steam(hot water,hot oil)control valve. According to the change of temperature of the medium(water or oil)being heated, it makes the heated medium(steam, hot water, hot oil) flow rate automatically adjusting. It is widely used in steam adjusting of heating installations both marine and onshore.

基本參數 Basic Parameters

雙溫包補償式感溫器 Double-probe compensation

型號
Model
公稱感溫包容積比
Nominal Volume ratio of probe V(一)/V(二) V(first)/V(second)
感溫包(一)
Probe(second)
感溫包(二)
Probe(second)
反應時間S
Response time
感溫包長度mm
Length of probe
柱塞最大提升度mm
Max lifting height of plunger
行程變化率
mm/℃
Stroke change rate
適用溫度范圍℃
Temperature adjusting range
行程變化率
mm/℃
Stroke change rate
適用溫度范圍℃
Temperature adjusting range
S4-0.5A 0.35/1 0.5 0~120 0.175 20~30 ≤25 420 12
S4-0.5B 0.5/1 0.25
S4-0.5C 0.7/1 0.35
S4-0.5D 1/1 0.5
S4-0.5E 1.4/1 0.7

說明Note:

1、毛細管標準長度為-3米,需要其他長度,應在訂貨時說明,最大長度為20米。 
The standard capillary tube length is three (3) meters, other lengts up to twenty (20) meters are available upon request specified in your order.
2、反應時間系指在液體介質內。 
The response time means the time responsed in liquid medium.

單溫包感溫器 Single-probe temperature sensor

型號
Model
行程變化率mm/℃
Stroke changerate
適用溫度范圍℃
Temperature adjusting range
反應時間S
Response time
感溫包長度mm
Length of probe
柱塞最大提升度mm
Max lifting height of plunger
D4-0.3 0.25 0~160 ≤25 420 12
BD4-0.3 150
D4-0.5 0.5 0~120.40~160 420
BD4-0.5 300
D4-1.0 1 0~60.30~90
60~120
420
BD4-1.0 400

說明Note:

1、毛細管標準長度為-3米,需要其他長度,應在訂貨時說明,最大長度為20米。 
The standard capillary tube length is three (3) meters, other lengts up to twenty (20) meters are available upon request specified in your order.
2、反應時間系指在液體介質內。 
The response time means the time responsed in liquid medium.

蒸汽調節閥 Steam control valve

型號
Model
公稱通徑mm
Nominal bore
適用介質
Using medium
熱源介質 材料
蒸汽 Steam 熱水 Hot water

額定蒸汽流量kg/h
Rated steam flow rate

最大允許壓差MPa(kgf/cm2)
Max allowable prssure differense

額定流量kg/h
Rated flow rate

最大允許壓差MPa(kgf/cm2)
Max allowable prssure differense
1F1.6-15 15 蒸汽熱水
Steam hot water
110 1.764 0.85 1.59 鑄鐵
Castiron
鑄鋼
Cast steel
不銹鋼
Stainless Steel
1F1.6-20 20 200 0.735 1.54 0.686
1F1.6-25 25 320 0.440 2.26 0.441
1F1.6-32 32 520 3.725 4.00 3.629
2F1.6-40 40 800 2.157 6.00 1.569
2F1.6-50 50 1400 1.863 9.5 1.529
2F1.6-65 65 2000 0.980 15.2 0.980
2F1.6-80 80 3200 0.784 24 0.746
2F1.6-100 100 5000 0.588 37.00 0.530
2F1.6-125 125 7812 0.3 58 0.3
2F1.6-150 150 11250 0.19 83 0.19

三通熱水調節閥 3 way hot water control valve

型號
Model
公稱通徑
Nominal bore
適用介質
Using medium
額定熱水流量t/h
Rated hot water flow rate
材料
Material
3F1.6-2.5 25 熱水
(hot water)
2.26 鑄鐵
鑄鋼
不銹鋼
castiron
cast steel
stainless steel
3F1.6-32 32 4.00
3F1.6-40 40 6.00
3F1.6-50 50 9.5
3F1.6-65 65 15.5
3F1.6-80 80 24
3F1.6-100 100 37

型號表示方法 The model indicating method is listed below

蒸汽調節閥 Steam control valve:

三通熱水調節閥 Three (3) way hot water control valve
3 F 1.6 - 100 
100 公稱通徑mm Nominal bore(in mm)
1.6 公稱壓力MPa Nominal pressure (in Mpa) 
F 連接方式:F-法蘭 Connection method:F-flange connection
3 三通 Three (3) way

外形和安裝尺寸 Outline and installation dimensions

雙溫包補償式感溫調節器外形和安裝尺寸
The outline and installation dimensions of double-probe compensation temperature controller
螺旋形單溫包感溫調節器外形和安裝尺寸
The outline and installation dimensions of spiral single-probe temperature controller

棒形單溫包感溫調節器外形和安裝尺寸
The outline and installation dimensions of rod single-probe temperature controller

型號
Model
L E G G
BD4-0.3 150 22 ZG1" M36×2
BD4-0.5 300 22 ZG1" M36×2
BD4-1.0 400 23 ZG1" M36×2
BD8-1.0 710 25 G1 1/4" M36×2

1F-1.6型蒸汽調節閥外形和安裝尺寸
The outline and installation dimensions of 1F-1.6 steam control valve

2F-1.6型蒸汽調節閥外形和安裝尺寸
The outline and installation dimensions of 2F-1.6 steam control valve

3F1.6-25~50熱水調節閥外形和安裝尺寸
The outline and installation dimensions of 3F1.6-25~50 hot water control valve

圖片
海靡訂貨須知:(國家標準)
一、A:產品名稱、型號、公稱通徑B:介質及溫度、壓力范圍C:是否有附件、交貨期、特殊要求等以便我們的為您正確選型。
二、若已經由設計單位選定我公司的閥門型號,請您根據閥門參數直接與我們銷售中心訂購。
三、當您使用的場合非常重要或環境比較復雜時,請您提供設計圖紙和詳細參數,我們的工程師專家會專心為您審核與分析。我們可以為您提供專業的解決方案,包括設計、定做、成套、運行、服務。我們一直致力于閥門行業領域的領導者,為您提供最新的閥門知識、最好的服務、最佳的技術顧問。
感謝您訪問我們的網站【电子捕鱼器线路 www.iwmejt.com.cn】,如有任何疑問,您可以致電給我們,我們一定會盡心盡力為您提供優質的服務。本廠專業提供船用蝶閥、船用閘閥、船用止回閥、船用調節閥、船用減壓閥、船用呼吸閥、高速透氣閥、船用快關閥、船用自閉閥、船用旋塞閥、船用消防閥、船用通海閥、船用防浪閥、船用濾器、船用空氣帽、船用球閥、船用截止閥、船用截止止回閥、船用閥組、船用截止閥箱、船用針型閥、船用電磁閥、船用隔膜閥、船用壓力表閥等各類閥門。
圖片